收藏本站
Secure digital input/output interface (SDIO)
Table 128. Card status
RM0008
Bits
Identifier
Type
Value
Description
Clear
condition
The command address argument was out
of the allowed range for this card.
31
ADDRESS_
OUT_OF_RANGE
ERX
’0’= no error
’1’= error
A multiple block or stream read/write
operation is (although started in a valid
C
address) attempting to read or write
beyond the card capacity.
The commands address argument (in
accordance with the currently set block
length) positions the first data block
misaligned to the card physical blocks.
30
ADDRESS_MISALIGN
’0’= no error
’1’= error
A multiple block read/write operation
(although started with a valid
C
address/block-length combination) is
attempting to read or write a data block
which is not aligned with the physical
blocks of the card.
Either the argument of a
SET_BLOCKLEN command exceeds the
maximum value allowed for the card, or
29
BLOCK_LEN_ERROR
’0’= no error
’1’= error
the previously defined block length is
illegal for the current command (e.g. the
host issues a write command, the current
C
block length is smaller than the maximum
allowed value for the card and it is not
allowed to write partial blocks)
28
ERASE_SEQ_ERROR
’0’= no error
’1’= error
An error in the sequence of erase
commands occurred.
C
27
26
25
24
23
22
21
20
ERASE_PARAM
WP_VIOLATION
CARD_IS_LOCKED
LOCK_UNLOCK_
FAILED
COM_CRC_ERROR
ILLEGAL_COMMAND
CARD_ECC_FAILED
CC_ERROR
EX
EX
SR
EX
ER
ER
EX
ER
’0’= no error
’1’= error
’0’= no error
’1’= error
‘0’ = card
unlocked
‘1’ = card locked
’0’= no error
’1’= error
’0’= no error
’1’= error
’0’= no error
’1’= error
’0’= success
’1’= failure
’0’= no error
’1’= error
An invalid selection of erase groups for
erase occurred.
Attempt to program a write-protected
block.
When set, signals that the card is locked
by the host
Set when a sequence or password error
has been detected in lock/unlock card
command
The CRC check of the previous command
failed.
Command not legal for the card state
Card internal ECC was applied but failed
to correct the data.
(Undefined by the standard) A card error
occurred, which is not related to the host
command.
C
C
A
C
B
B
C
C
480/995
Doc ID 13902 Rev 9
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MCBTMPM330 BOARD EVAL TOSHIBA TMPM330 SER
MCIMX25WPDKJ KIT DEVELOPMENT WINCE IMX25
MCIMX53-START-R KIT DEVELOPMENT I.MX53
MCM69C432TQ20 IC CAM 1MB 50MHZ 100LQFP
MCP1401T-E/OT IC MOSFET DRVR INV 500MA SOT23-5
MCP1403T-E/MF IC MOSFET DRIVER 4.5A DUAL 8DFN
MCP1406-E/SN IC MOSFET DVR 6A 8SOIC
MCP14628T-E/MF IC MOSFET DVR 2A SYNC BUCK 8-DFN
相关代理商/技术参数
MCBSTM32EXLU 功能描述:开发板和工具包 - ARM EVAL BOARD + ULINK2 FOR STM32F103ZG RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
MCBSTM32EXLU-ED 制造商:ARM Ltd 功能描述:KEIL STM STM32EXL EVAL BOARD
MCBSTM32EXLUME 功能描述:开发板和工具包 - ARM EVAL BOARD + ULINKME FOR STM32F103ZG RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
MCBSTM32F200 功能描述:开发板和工具包 - ARM EVAL BOARD FOR STM STM32F207IG RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
MCBSTM32F200U 功能描述:开发板和工具包 - ARM EVAL BOARD FOR STM STM32F207IG + ULINK2 RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
MCBSTM32F200UME 功能描述:开发板和工具包 - ARM EVAL BOARD FOR STM STM32F207IG ULINK-ME RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
MCBSTM32F200UME-ED 制造商:ARM Ltd 功能描述:KEIL STM32F207IG EVAL BOARD
MCBSTM32F400 功能描述:开发板和工具包 - ARM EVAL BOARD FOR STM STM32F407IG RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V